The amplifier (AMP6) is the circuit board driving the motor in most TigerStop positioners. AMP6 is compatible with TigerStop and HeavyDuty.
#103700301
Important things to note when ordering this part:
The Amplifier (AMP6) is shipped without the aluminum Cover (MBC2). It is recommended to order the aluminum cover with your Amplifier.
AMP6 requires a Controller (CON5) and is not compatible with older controllers.
It's important to test the motor before ordering an AMP6, because a damaged motor can destroy a fresh amplifier.
AMP6 orders require the serial number of the machine that will receive the electronics. Please enter the serial number in the notes box during checkout, or email webshop@tigerstop.nl. This item cannot ship without receipt of the serial number.
If you are unable to determine your serial number please contact sos@tigerstop.nl for additional support or watch the below videos.
TigerStop DC Servo Motor 3,73:1
MOTOR
Regular price
€1.360,00
/
This TigerStop DC Servo Motor has a gearbox ratio of 3,73:1 and is used for TigerStop machines.
#101420102
TigerStop DC Servo Motor 9,5:1
MOTOR-9.5:1
Regular price
€1.348,00
/
This TigerStop DC Servo Motor has a gearbox ratio of 9,5:1 and is used on TigerAngle machines.
#101420201
I/O Panel
I/O PANEL
Regular price
€735,00
/
The I/O panel interfaces with peripheral devices including bar code scanners, printers, clamps, and Standard Interconnect Kits (SIK). The I/O Panel can be used with TigerStop and HeavyDuty. The I/O panel is compatible with the Controller (CON5) and Amplifier (AMP6), and cannot be used with older electronics. This part ships with a 3 meter (10 foot) version 5 controller cable (CC5-10).
#103730301
Please note the following about ordering this item:
I/O panel orders require the serial number of the machine that will receive the electronics. Please enter the serial number in the notes box during checkout or send this information to webshop@tigerstop.nl. This I/O Panel cannot be shipped otherwise.
Failure to use the I/O panel with the specified serial number can result in software compatibility issues. Learn how to locate your serial number in the below video.
If you still have questions about ordering this part, please contact sos@tigerstop.nl for further information.
Idle End Sensor 3m
IES2-10
Regular price
€91,00
/
3 meter idle end sensor (also known as the far end sensor) for TigerStop. The idle end sensor signals the limit of travel far from the motor. IES2-10 is an idle-end sensor for a 3 meter working length TigerStop.
Note: Learn how to troubleshoot the idle end sensors bywatching this informational video.
#100990101
Idle End Sensor 4.8m
IES2-16
Regular price
€91,00
/
The idle end sensor signals the limit of travel far from the motor. IES2-16 is an idle-end sensor for a 4.8m working length TigerStop.
Note: Learn how to troubleshoot the idle end sensors by watching this informational video.
#100960201
Idle End Sensor 6.8m
IES2-22
Regular price
€91,00
/
The idle end sensor signals the limit of travel far from the motor. IES2-22 is an idle-end sensor for a 6.8 meter working length TigerStop. Note: Learn how to troubleshoot the idle end sensors by watching this informational video.
#100980101
Idle End Sensor 8.5m
IES2-30
Regular price
€91,00
/
The idle end sensor signals the limit of travel far from the motor. IES2-30 is an idle-end sensor for both an 8.5 and a 9.2 meter working length TigerStop.
Note: Learn how to troubleshoot the idle end sensors bywatching this informational video.
#100980103
Motor Plate Bearing
MPB
Regular price
€20,00
/
This is the bearing for the TigerStop motor mount.
#415960101
Motor End Sensor
MES2
Regular price
€91,00
/
The Motor End Sensor (MES2) signals the limit of travel near the motor. It is compatible with TigerStops of any length.
#100950101
Motor End Pulley
ATP
Regular price
€59,00
/
This pulley is compatible with TigerStops using a 32mm (1.26") width belt. It also ships with a roll pin.
#102600101
Motor Box End Cap and Gasket
MBEC2
Regular price
€60,00
/
This is a replacement end cap for the Amplifier (AMP6).
#104200102
Motor Encoder Cable
ENCC-B
Regular price
€35,00
/
The Motor Encoder Cable connects motors to the Amplifier (AMP6) in a TigerStop. This cable is not compatible with other motor types (TigerSaw 1000, TigerSaw 2000, or HeavyDuty).
#101400101
Motor Box Cover
MBC2
Regular price
€60,00
/
This is a replacement aluminum cover for the Amplifier (AMP6).
#104190201
Encoder
ENC
Regular price
€227,00
/
This rotary Encoder works with TigerStop. The cable connecting the encoder to the amplifier is included.
#101390101
Idle End Sensor 2m
IES2-06
Regular price
€83,00
/
2 meter idle end sensor (also known as the far end sensor) for TigerStop. The idle end sensor signals the limit of travel far from the motor. IES2-06 is an idle-end sensor for a 2 meter working length TigerStop.
Note: Learn how to troubleshoot the idle end sensors bywatching this informational video.
#100960101
Idle End Sensor 4m
IES2-12
Regular price
€91,00
/
The idle end sensor signals the limit of travel far from the motor. IES2-12 is an idle-end sensor for a 4m working length TigerStop.
Note: Learn how to troubleshoot the idle end sensors by watching this informational video.
#100960201
HeavyDuty Motor (AC)
MOT-HD
Regular price
€1.445,00
/
This motor is for HeavyDuty machines.
#102660101
Idle End Sensor 7.4m
E-IES7.4
Regular price
€83,00
/
7.4 meter idle end sensor (also known as the far end sensor) for TigerStop. The idle end sensor signals the limit of travel far from the motor.
Note: Learn how to troubleshoot the idle end sensors bywatching this informational video.
#100980102
Thank You For Shopping with TigerStop Europe!
Please note that most products must be installed by a TigerStop Certified Technician or Dealer.
We kindly ask that you list your preferred Dealer's name in the notes section during checkout.